Petrol engine 1.5 TSI (DADA) - location of sensors and components

Installation location overview - engine 1.5 TSI (DADA) compartment
Installation location overview - engine compartment of 1.5 TSI petrol engines

Engines 1.5/110 kW TSI EVO
Engine code: DADA .

These engines are also installed on: VW Arteon (3H7), VW T-Roc (A11), VW Golf 7 (BV5, BQ1), VW Golf Sportsvan (AM1, AN1), Skoda Karoq (NU7), Skoda Octavia 3 A7 (5E3, 5E5, NL3), Audi A3 (8VK, 8VF, 8VE, 8VM), SEAT Ibiza 5 (KJ1), SEAT Arona (KJ7).

1 - Lambda probe 1 in front of the catalytic converter GX10 comprises:
Lambda probe G39
Lambda probe heater Z19
2 - Connector for Lambda probe 1 before catalyst GX10 and Lambda probe 1 after catalyst GX7
3 - Plug holder
4 - Ignition coils with a power output stage
Ignition coil 1 with power output stage N70
Ignition coil 2 with power output stage N127
Ignition coil 3 with power output stage N291
Ignition coil 4 with power output stage N292
When installing new spark plugs, grease the ignition coils with power output stage with lubricating paste G 052 565 A1 .
5 - Position sensor for intake camshaft G1002
6 - Module for air mass measurement GX35 (not fitted to all engines) comprises:
Air mass meter G70
Temperature sensor in the air mass meter G1005
7 - Coolant temperature sender at radiator outlet G83
8 - Activated charcoal filter solenoid valve 1 N80
9 - Charge pressure sender GX26 comprises:
Charge pressure sender G31
Intake air temperature sender G42
10 - Throttle valve control unit GX3 comprises:
Throttle valve control unit J338
Throttle valve drive for electronic power control G186
Throttle valve drive angle sensor 1 for electric power control G187
Throttle valve drive angle sensor 2 for electric power control G188
11 - Intake manifold pressure sender GX9 comprises:
Intake air temperature sender 2 G299
Intake manifold pressure sender G71
12 - Vacuum pump for brake V192
13 - Camshaft control valve 1 N205

Contact assignment at bulkhead plenum chamber

1 - Lambda probe 1 in front of the catalytic converter GX10
2 - Lambda probe 1 after catalytic converter GX7

Installation location overview: engine 1.5 TSI from top

1 - Camshaft control valve 1 N205
2 - Camshaft adjustment valve 1 in the outlet N318
3 - Position sensor for exhaust camshaft G1003
4 - Ignition coil 1 with power output stage N70
5 - Ignition coil 2 with power output stage N127
6 - Exhaust cam adjuster for cylinder 2 N587
7 - Ignition coil 3 with power output stage N291
8 - Exhaust gas pressure sensor 1 G450
9 - Exhaust cam adjuster for cylinder 3 N595
10 - High pressure pump with fuel dosage valve N290
11 - Ignition coil 4 with power output stage N292
12 - Position sensor for intake camshaft G1002
13 - Inlet cam adjuster for cylinder 2 N583
14 - Inlet cam adjuster for cylinder 3 N591
15 - Charge pressure sender GX26
16 - Throttle valve control unit GX3 comprises:
Throttle valve control unit J338
Throttle valve drive for electronic power control G186
Throttle valve drive angle sensor 1 for electric power control G187
Throttle valve drive angle sensor 2 for electric power control G188
17 - Intake manifold pressure sender GX9 comprises:
Intake air temperature sender 2 G299
Intake manifold pressure sender G71

Installation overview: engine 1.5 TSI from front

1 - Knock sensor 1 G61
2 - Oil pressure sender G10
3 - Fuel pressure sender G247
4 - Camshaft control valve 1 N205
5 - Injection valves
Injection valve for cylinder 1 N30
Injection valve for cylinder 2 N31
Injection valve for cylinder 3 N32
Injection valve for cylinder 4 N33
6 - Position sensor for intake camshaft G1002
7 - Module for engine temperature control GX33 comprises:
Position sensor for engine temperature control G1004
Actuator for engine temperature control N493
8 - Engine speed sender G28
9 - Charge air cooler pump V188

Installation overview: engine 1.5 TSI from rear

1 - Module for charge pressure regulation GX34
Note: Different designs are shown in the figure. comprises:
Charge pressure regulator V465
Position transmitter for charge pressure regulator G581
2 - Lambda probe 1 in front of the catalytic converter GX10 comprises:
Lambda probe G39
Lambda probe heater Z19
3 - Lambda probe 1 after catalytic converter GX7 comprises:
Lambda probe downstream of catalytic converter G130
Lambda probe heater 1 downstream of catalytic converter Z29
4 - Oil pressure control valve N428
5 - Oil level and oil temperature sender G266
6 - Coolant temperature sensor at engine output G82
7 - Coolant temperature sender G62